Plumbing Basics: Your Key to Bathtub Installation
Plumbing Basics: Your Key to Bathtub Installation
Blog Article
What're your opinions concerning Tools You Need to Install a New Bathtub ?
Mounting a bath tub isn't exactly rocket science, but it does need strong plumbing, woodworking, and also occasionally, tiling skills. Replacing an old bath tub with a new one is likewise a reasonably tough job. If the old tub is readily available, the project can move rapidly; if you need to open a wall to get rid of the old bathtub and also place the new bath tub, the job is much harder. In either situation, the project is within a home handyman's skills, although you will certainly require a helper to vacate the old bathtub as well as set in the new one. See to it you have actually qualified on your own for the task and also are comfortable trying it. Instead of employing a specialist to take over a halfway-completed task, it is better to take into consideration utilizing one prior to you begin. Possibilities are you may need a specialist plumber to make tube connections.
This write-up will assist you mount a new tub in your restroom if you have actually already acquired a new bathtub and don't require to change the setup of your previous water pipes.
Your devices and also material list should make up the following:
Planning for the Installation
Firstly, the sustaining framework provided with the bathroom needs to be fitted (if needed) according to the producer's directions. Next, fit the taps or mixer to the tub. When fitting the tap block, it is important to make certain that if the faucet comes with a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the faucets system to stop strain on the tub.
Fit the versatile faucet ports to the bottom of the two taps utilizing 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet with the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you utilize every one of the provided washing machines.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath need to currently prepare to be fitted in its last position.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installation, after that the first thing you ought to do is separate the supply of water. After doing so, turn on the taps to drain any water remaining in the system. The procedure of getting rid of the existing taps can be fairly troublesome because of the restricted accessibility that is commonly the situation.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a fabric all set for the staying water that will certainly come from the pipelines. Once the supply pipes have been gotten rid of, use the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single faucets from transforming during this process. When the faucets have actually been removed, the holes in the bath/basin will need to be cleansed of any type of old securing substance.
Before carrying on to fit the brand-new taps, contrast the pipeline links on the old faucets to the brand-new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the brand-new taps to fit.
Installing the Tub
Making use of the two wooden boards under its feet, put the tub in the required position. The wooden boards are handy in equally spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto four small points.
The next objective is to make certain that the bath tub is leveled all round. This can be accomplished by inspecting the level as well as changing the feet on the bathtub till the level checks out level.
To mount faucets, fit all-time low of the furthest versatile tap port to the appropriate supply pipeline by making a compression join; after that do the exact same for the other faucet.
Switch on the water as well as examine all joints as well as brand-new pipework for leaks as well as tighten them if necessary. Fill up the bathtub and additionally check the overflow electrical outlet and also the normal outlet for leakages.
Ultimately, deal with the bathroom paneling as described in the maker's instruction manual. Tiling and also securing around the bathtub ought to wait till the bathtub has been utilized at the very least when as this will settle it right into its last position.
Suitable New Touches
If the tails of the new taps are plastic, then you will certainly require a plastic port to avoid damage to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the other end supplies a connection to the existent supply pipes.
If you require to fit a monobloc, then you will certainly require reducing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, place the tap in the placing opening in the bath/basin making sure that the washers remain in place between the faucet as well as the sink. Secure the faucet in place with the maker provided backnut. As soon as the faucet is firmly in place, the supply pipes can be attached to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with typical faucet adapters. The previous kind needs to be connected to the tap finishes initially, tightening up just by hand. The supply pipelines can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the location where the bath meets the ceramic tile, it is required to secure the joins with a silicone rubber caulking. This is important as the fitting can move sufficient to fracture a rigid seal, triggering the water to pass through the wall between the bathroom and also the tiling, resulting in issues with wetness and also feasible leaks to the ceiling below.
You can pick from a variety of coloured sealers to assimilate your fixtures and also installations. They are marketed in tubes and cartridges, and also are capable of sealing voids as much as a size of 3mm (1/8 inch). If you have a larger void to fill, you can fill it with twists of drenched paper or soft rope. Remember to always load the bathtub with water before sealing, to enable the activity experienced when the bathtub is in use. The sealant can break relatively very early if you do not take into consideration this activity before securing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise easily readily available on the marketplace. It is suggested to fit the floor tiles using waterproof or water resistant adhesive and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was brought to that report on Tools You Need to Install a New Bathtub from someone on our other web blog. Sharing is caring. Helping people is fun. Thanks for your time. Visit us again soon.
Plumbing integrity assured. Report this page